Posted by Ash
This post may contain affiliate links to products we personally use and love.
With summer approaching, Eileen was working hard on her flower garden. As I saw her walking all the way up to the house and back out to the yard to fill up her watering can several times in a row, inspiration struck.
Why not set up a type of water reservoir by her garden?
Not only would this eliminate her water laps to the house, but it would avoid the hassle of rolling/unrolling a hose.
Furthermore, I could use a rain barrel system which would fall right in line with our new organic way of life. We’ve made a lifestyle change this year, opting for organic, non-processed foods, and re-using rainwater was a perfect addendum.
So I did some research on rain barrel reservoirs and settled on a design pattern I liked.
A rain barrel reservoir is a very simple way to collect and store rainwater for future use. You first need a large container to store the water.
A typical container used is the blue 55-gallon water drums with bung hole caps on the top. In my research, I actually found out that a lot of cities offer water conservation programs and give out these drums for free.
You can probably even check with businesses or food processing factories to see if they are throwing any away.
I opted for a different route though. I did not need a large 55-gallon container. I shopped around at Home Depot and found a 20-gallon plastic garbage can for $13 that was perfect.
I really liked the lid too because when I flipped it over, it was deep and round. This meant it would serve as a nice water collection basin for the falling rain (as opposed to a flat surface that I would get with a water drum), allowing the water to pool in the center.
Here's a picture of the garbage can I purchased at Home Depot with the deep upside down lid:
The first step of construction was drilling five large drainage holes in the center of the lid. I used a hole saw bit for my drill to make these cuts.
Then I placed some mosquito screen on the part of the lid that would be facing the water, and secured it in place with some waterproof duct tape.
It was important to cover the drainage holes with insect screen to keep bugs out of the water. If the screen wasn't fine enough, mosquitoes especially would get in and lay larvae in the water.
I also had to drill an overflow hole in the top part of the garbage can. This was to allow water to drain out when the container was full to capacity. This hole also had to be protected with insect screen.
Here's a picture of the 5 drainage holes in the lid, as well as the overflow hole in the garbage can:
Below is a picture of what the lid looked like once the insect screen was applied with waterproof duct tape (the screen is a little hard to see, but its covering the holes).
This part of the lid would be facing downwards so would not be visible.
I needed a valve inserted at the bottom of the can to let water out when needed. I did some shopping online and found a really nice valve spigot with a bulkhead fitting that was perfect for my rain barrel design.
The bulkhead fitting was the piece that let me attach it to the wall of the garbage can without leaking.
To install it, I first drilled a hole at the bottom of the can. Then I inserted the inside part of the bulkhead fitting. This piece came with a rubber ring that would form a tight seal when pressed against the can wall.
Next, I attached the outside part of the fitting. It just screwed onto the inside piece from the outside, and then I used a wrench to make a tight connection.
Finally, I screwed on the actual spigot into the outside bulkhead fitting. I used some Teflon tape on the spigot grooves to ensure a watertight seal.
With the spigot tightly installed, I partially filled the can with water (just high enough to cover the spigot) and checked for leaks. No water came out, so it was good to go.
Here's a picture of the spigot (left) and bulkhead fitting (right), straight out of the box:
Here's a picture of the installed spigot from the outside (notice the white Teflon tape around the spigot groove to make a waterproof seal with the bulkhead fitting):
Here's what the bulkhead fitting looked like from the inside:
Next, I had to secure the upside down lid to the garbage can so that a gust of wind wouldn't send it soaring through the air. I came up with a simple technique of drilling 16 small holes around the perimeter of the lid penetrating the can below.
Then I inserted 6 inch U shaped strands of electrical wire into the holes, twist tying the bottoms. The wires held the lid tightly to the garbage can.
Here's a picture showing the wire strands holding down the lid:
The rain barrel was now finished, but the project would not be complete without a proper stand for the barrel. The barrel needed to be elevated about a foot off the ground to allow buckets and watering cans to be placed under the spigot.
I came up with a simple but very sturdy design for a stand using wood left over from my shed project.
It was important to use pressure-treated wood for the stand as it would be in direct contact with the ground and be exposed to bugs. I constructed the stand as outlined in the pictures below.
I cut 2’ lengths of 2 x 4s, 2 x 6s (pictured below) and 1’ length of 4 x 4s (not pictured):
Then, I attached 4 of the 2 x 6s to 4 vertical 4 x 4s:
Next, I attached 2 of the 2 x 4s to the top of the 4 x 4s (these were to serve as the supports for the stands platform):
Finally, I attached 4 of the 2 x 6s to the top, completing the stand:
With the stand and rain barrel now complete, I found a good location near to Eileen's garden and set it up.
I also made sure there were no tree branches above to block the rainfall. At this point, I realized I forgot to properly secure the rain barrel to the stand.
A strong gust of wind would knock over an empty barrel. So I screwed in 2 metal hooks into the stand and tied the garbage can handles to them with some carabiner style bungee cords.
Here is a picture of the final setup:
Here's a close up of the hook for the bungee cord:
I was excited for Eileen to start using the rain barrel. Now I just had to wait for rain to test it out.
Luckily it rained the next day and I ran out after the skies cleared up to check out the rain barrel.
My simple design worked pretty well. I opened the spigot and water came pouring out. Though, it wasn't that much water for the amount of rain that fell.
The garbage can lid only has so much surface area to collect water and yielded a small amount of water. It would take several large rain falls to collect a usable amount of water.
So although the basic design for the rain barrel was complete, I was already envisioning upgrades to improve the water collection efficiency.
Updates to come in future blog posts!
As for time and cost, the materials for the rainwater barrel cost $35, and it took about an hour to make.
Want to see more? Check out our similar projects.
Hi! We're Ash and Eileen, and we are sharing our home project stories with you. From crafty projects to home maintenance to more ambitious DIY endeavors, we hope our stories inspire you to check a few things off your project list! :)