With the warm weather, Ash and I have been working on so many projects – a built-in bookshelf in our sitting room, a planter box for our garden, painting an old thrift store desk, transforming a kitchen desk area to a cabinet, and refinishing an old telephone table.
Today I’m sharing how Ash and I refinished our old telephone table.
I found it for $20 at my favorite flea market years ago and feel in love with its charm. I’d been wanting to stain it dark for years, but it fit in pretty nicely at our old house.
However, in our new house, our family room is much more modern looking, and this old telephone table stood out like a sore thumb!
Preparing the Telephone Table
I was excited to finally have a chance to redo this old telephone table.
My plan was to use wood stain, as we redid my nanny’s coffee table years ago with wood stain. It turned out beautiful.
The first thing I did was wipe it down really well, getting rid of any dust. Then I started to sand down table.
Here’s where I made my mistake. I didn’t sand it down to bare wood. I just did a light sanding, enough to give the stain something to stick too.
Mistakenly, I then moved onto staining the piece, and it was turning out horribly. Since I didn’t sand this old, weathered piece down to bare, there were lots of little knicks and grooves in the surfaces. The stain was filling these in, turning them almost black. So, the surfaces were looking spotty and uneven.
I figured that I now had three choices: I could switch gears and use gel stain like I did on the kitchen and bathroom cabinets, I could paint the table, or I could start over again and sand it down to bare wood.
I decided to sand it down to bare wood and start again. Here’s where Ash helped me. We decided to leave the rungs as is – they looked fine with the first coat of stain, and we were hoping they would blend in well with the second application of stain.
To begin the sanding, Ash started with the random orbital sander and 80 grit paper. However, the existing finish on the table proved to be very challenging to remove. The sander was doing its job but very slowly and burning through lots of paper.
After some experimentation with different tools, Ash found the best one to be the oscillating multi-tool.
Using a flush-cut saw blade, running the blade against the surface at the right angle scraped off the thick, difficult finish. It did leave behind a very ragged surface due to the oscillating action of the blade, but he sanded it down smoothly after with the orbital sander.
One caution about using the oscillating multi-tool is that Ash had to be careful to pull the blade versus pushing it through.
When he pushed the tool, it would sometimes snag a groove and start cutting deeply into the wood. The pulling action worked out best.
I made sure to wipe off all of the sawdust – using a combination of a cheese cloth and Ash’s Shop-Vac.
Staining the Telephone Table
Next, I re-gathered my materials for staining:
- Dark Walnut Wood Stain – Minwax
- Polyurethane – Minwax
- Pre-stain – Minwax
- Four rags (two per coat)
- Foam brushes
I prefer to stain wood using rags because the stain rubs into the wood better. You have less excess and build-up; however, I keep the foam brush around for hard to get to places.
Also, I grabbed our can of pre-stain since the wood was now bare. I used the pre-stain first, brushing it on with a foam brush and waiting about 20 minutes before starting to stain.
I used the first rag to rub on a nice coat of stain. Then, I started with the seat and worked my way around.
Since I was working in the hot sun, the wood was absorbing the stain faster than usual. So, I needed to wipe off the excess before I finished the whole piece. I used the second rag for this, lightly brushing it along the surface. Don’t skip this step – or you will end up with globs.
Also, make sure to do a good job removing the excess around tight areas – like where the rungs meet the table. Otherwise, you will end up with ugly, globby lumps.
Even though I used the rag for most of the staining, I took out the foam brush to get the really tight corners or spaces. Be careful with the foam brush because it holds a lot of stain and drips easily and messily.
After I was done staining and removing the excess, I did a quick scan to make sure I didn’t miss any drips. I let it dry until it wasn’t tacky anymore.
Then, I put on another coat.
Sealing the Stain with Polyurethane
After I was done with the two coats, I was pleased with the results. So, Ash put on a coat of polyurethane.
He used a foam brush, going along with the grain of the wood, and carefully making sure there were no lingering air bubbles on the table’s surfaces.
He let that dry overnight and then did another coat. The refinished telephone table was almost done.
Completing the Refinished Telephone Table
The last step was choosing a new knob at Home Depot and screwing it into the drawer.
We let the refinished telephone table air out for a few days, and then moved it back into our family room.
Here’s a before and after picture of my charming newly refinished telephone table.
Since we had all of the wood staining materials in our garage, the cost of refinishing the telephone table was $2. Just the cost of the knob. 🙂
The time of project spanned about a week or so, due to the dry time between coats and the couple of days we let it air out. While the refinished telephone table was drying, Ash and I had other projects we were working on – like a desk update.
Overall, the telephone table update was quite an improvement. The dark stain modernized the old table perfectly. I’ll be on the lookout for my next flea market find 🙂